Pick your old Dometic. See how it is wired today, then watch where each wire goes on the back of the UST 3.0.
1Pick your old Dometic
2How it is wired today
Behind it
The most common Dometic. Behind it are just 3 wires. Two bring power. The third is a signal wire: the thermostat sends every command to the AC over that one wire.
A real one with the cover off. The 3 wires sit in the blue block at the top left: green on GND, white in the middle, red on +12V.
Behind it
The older Comfort Control. Five buttons: Mode, Fan, Up, Down and Zone. Behind it is one phone-style cable. That one cable carries the power and every command.
Behind it
The wide Comfort Control Center found in many fifth wheels and motorhomes. It runs more than one zone. Behind it is one phone-style cable. That one cable carries the power and every command.
Behind it
The newer Dometic thermostat, used with Dometic FreshJet R32. Its cable has a wider plug, so you need Dometic's adapter (RJ45 to RJ11) to turn it into a phone-style plug. Check the part number on the back of the old thermostat: 9610007991 works. 4471011652 does not.
3Where it goes on the UST 3.0
This is the back of the UST 3.0. Every hole has a number.
That’s it.
Pick your old thermostat.
Wire colors can vary. Match by the old thermostat’s labels.
Wiring steps for each Dometic thermostat
Dometic single zone (round or square)
Red +12V goes into 7.
Cut the black jumper in half. One half goes into 8.
The other half goes into 16. Join both halves and the ground wire with a wire nut.
White signal wire goes into 11.
Dometic 5-button
Unplug it from the old thermostat, plug it in here.
Dometic 10 or 12-button
Unplug it from the old thermostat, plug it in here.
Dometic Connect Essential
Add Dometic's RJ45-to-RJ11 adapter to the Connect Essential cable, then plug it in here.
Ground: one wire per hole
Each hole takes only one wire. Holes 8 and 16 both need the ground wire. So cut the black jumper from the box in half. Push one half into 8 and the other half into 16. Then twist both halves and the ground wire together under one of the orange wire nuts from the box. A wire nut is the better way to do this. It holds all three wires tight, and each hole only has to grip one wire.
4Do it, step by step
Turn the power off. Unplug shore power, shut off the generator and turn off the battery switch.
Take a photo of the back of the old thermostat before you undo anything.
Take the old thermostat off the wall and free its wires or cable.
Put the 3 screws in the wall. There is no back plate. Tape the paper template from the box to the wall. It shows where each screw goes. Put in the anchors and the 3 screws, and leave the screw heads sticking out a little. Keep the wires hanging out of the wall.
Connect it. The wires push straight into the back of the thermostat. Red goes into 7. White goes into 11.
Ground: holes 8 and 16 both need the ground wire, and each hole takes only one wire. Cut the black jumper in half. Push one half into 8 and the other half into 16. Then twist both halves and the ground wire together under a wire nut.
Strip about 1/4 inch of each wire, push it in until it locks, and give it a gentle tug.Plug the phone-style cable into the jack in the middle of the UST 3.0 back until it clicks. Do not cut the cable. No other wires are needed.Plug the phone-style cable into the jack in the middle of the UST 3.0 back until it clicks. Do not cut the cable. No other wires are needed.Put Dometic's adapter on the cable. Then plug the phone-style end into the jack in the middle of the UST 3.0 back until it clicks.
Hang the thermostat. Push it onto the 3 screws and slide it until it locks on all three. Then tighten the travel lock screw on the bottom edge so it cannot slide off. Turn the power back on.
Tell it what you have. Tap Dometic, then the Single-Zone choice that matches your heat: furnace only, heat pump + furnace, or heat strip + furnaceMulti-Zone, 5 button CCC. On the next screen, always pick Heater 1: Heat Pump, Heater 2: Heat Strip, Heater 3: Furnace. Pick these even if you do not have all three. Nothing else works on this systemMulti-Zone, CCCMulti-Zone, FreshJet R32. See this screen. No setup screen? Many thermostats leave the factory already set to another system. Start fresh first: see Controller and heaters.
To take a wire back out, press the small white button next to its hole and pull.
These Dometic systems do not work with UST 3.0
Dometic 4-button thermostat (only Fan, Mode, Up and Down)
Variable-speed Dometic AC units
Dometic systems run from one central touch screen, like OneControl, Firefly or iN-Command
Dometic AC units with a remote control and no wall thermostat
Atwood thermostat
Questions
How many wires does a Dometic single zone thermostat have?
Three: power, ground and one signal wire. On the UST 3.0, power goes into 7 and the signal wire into 11. Ground feeds both 8 and 16: cut the jumper in half, push one half into each hole, and join both with the ground wire under a wire nut.
How do I connect a Dometic Comfort Control Center to the UST 3.0?
Unplug the phone-style cable from the old thermostat and plug it into the jack in the middle of the UST 3.0 back. No other wires are needed.
Not sure which one you have?
Text a photo of your old wall thermostat to 1-844-WALTECH. Text only, no calls.