Home/Support/UST 3.0 guide

Step 4 of 5

The thermostat

Four short videos. Watch one, try it on your thermostat, then watch the next.

1

Understanding your thermostat

The everyday part: temperature, cool, heat and fan. About 2 minutes.

Turn your sound on. Tap pause any time.

Read the steps
  1. On Home, tap Thermostat. Set the temperature you want with minus or plus.

  2. Tap Control at the top right. Cool and heat start off. They will not run until you turn them on here.

  3. Want cooling? Tap Cool 1. Want heat? Tap a heater. Lit means on.

  4. More than one heater? You see a box for each one. Light the one you want to use.

  5. On means ready, not running. It runs only when the room needs it. Example: you want 72. The room is 76, so the AC runs. At 72 it stops by itself.

  6. Auto: light Cool and a heater together. It cools when the room is too warm and heats when it is too cold.

  7. Fan on Auto: the fan runs only while the AC or heat pump is running.

  8. Fan on On: the fan runs all the time, even when the AC is not cooling.

  9. Fan speed: slide to Low or High. Some ACs also have Medium. Some AC controllers set the speed for you.

  10. Dry Mode runs the AC to dry the air.

2

Stay connected

Wi-Fi, cellular as the backup, and why Bluetooth and Zigbee stay on. About 2 minutes.

Turn your sound on. Tap pause any time.

Read the steps
  1. On Home, tap Settings, then Connections.

  2. Wi-Fi is the main way. On Wi-Fi the app works with no monthly fee. 2.4 GHz only.

  3. Cellular is the backup. It is built in and keeps the app working where there is no Wi-Fi. It needs the optional WalTech Cellular plan.

  4. With the plan, the thermostat moves to cellular by itself when Wi-Fi drops.

  5. Leave Bluetooth on. It talks to tank sensors, smart plugs and smart relays.

  6. Leave Zigbee on. It talks to door, leak and motion sensors.

  7. With Wi-Fi and Cellular both off, the app cannot reach the thermostat. The touch screen still works.

  8. The four icons at the top right of Home show what is on. Teal means on. Grey means off.

  9. Device Info has the QR code for the app, your device ID and error codes. Updates and Reboot has new software. Updates need Wi-Fi, or the thermostat's own hotspot with the app.

3

Fine tune heating and cooling

HVAC Settings, each one with an example. About 2 minutes.

Turn your sound on. Tap pause any time.

Read the steps
  1. Tap Settings, then HVAC Settings. Most owners never need to change these.

  2. Temperature Calibration: fixes a reading that is off. Example: the screen says 76 but your own thermometer says 74. Set it to -2.

  3. 2nd Heater Activation: how far the room must fall behind before the next heater helps. Example: set to 3 and you want 70. At 67 the second heater joins in.

  4. Temperature Differential: how far the room may drift before it starts. Example: set to 2 and you want 72. Cooling starts at 74. Raise it if your AC clicks on and off too often.

  5. No-Action Range: for Auto only. Example: set to 3 and you want 72. The heat set point is now 69 and the cooling set point is 75. Nothing happens between 69 and 75. With Temperature Differential at 2, heat starts at 67 and cooling starts at 77.

  6. Auto Generator (AGS): only if automatic generator start is wired to the thermostat. Otherwise leave it Off.

  7. B & O Settings: only for systems with a B&O valve. Most RVs leave it Off.

  8. Dry Mode humidity: the dampness target for Dry Mode. Example: set 50%. The AC runs to try to reach 50%. It may cool up to 2 degrees past your set temperature while it tries, then it stops.

4

Change the screen

Brightness, sleep time, and F or C. Under 1 minute.

Turn your sound on. Tap pause any time.

Read the steps
  1. Tap Settings, then Display Settings.

  2. Brightness: tap minus or plus.

  3. Screen goes dark: tap to choose Never or 1 to 30 minutes. Touch the screen to wake it.

  4. Temperature: pick F or C.

  5. Home screen shows: the temperature you set, or the room temperature.

  6. Changes are saved right away. There is no Save button.

More than one AC? Home shows a box for each zone. Tap a zone first, then do the same steps.

Step 4 of 5 is done. You are not finished yet: 1 more step to go.

Go to step 5: Smart Hub →

Questions

How do I change the temperature on the WalTech UST 3.0?

On Home tap Thermostat, then tap minus or plus or drag the white dot. Tap Control to turn cooling, heating and the fan on or off.

How do I switch the UST 3.0 between Fahrenheit and Celsius?

Tap Settings, then Display Settings, then tap F or C. The change is saved right away.

Stuck? Text a photo of your screen to 1-844-WALTECH. Text only, no calls.